3/17/2023 0 Comments Slate roofIt would be beneficial to future users of this specification sheet if current designers have any feedback in working with it. We hope this sheet can be put to good use and ease this process for the roof designer. References and Standards – NSA, ASTM, FM, and the Florida Building CodeĮxample of Completed Slate Specification Sheet Installation – Layout, field slates, eaves, valleys, ridge, hip Underlayments – Installation & product acceptability In this document you will find key information related to: It provides clear instructions on the intent, performance and construction of the project. of work to be done so designers, architects, engineers, or roof consultants can specify a slate roof properly. The punch can also be used for nailing purposes.The purpose of this 3-part specification is to provide a detailed description of the quality required, materials, workmanship, dimensions, etc. A cutter can also cut concave and convex cuts for decorative work. A slate cutter is light, transportable, and trims slate to size which makes it essential for repair work. Slate Cutter – Sometimes a piece of slate will not be an exact size match for a repair. The tool “hooks” over the ridge and uses gravity to hold the ladder in position while the user climbs the ladder. Once a ridge hook is secured to a ladder, the ladder is rolled up the roof and then turned over. Ridge Hook – If the roof has a ridge, and it’s accessible with a portable ladder, then the ridge hook is the quickest method for reaching a repair area. It doubles for hitting nails and installing slate hooks. You DO NOT want to use your treasured slate hammer. A heavier hammer is needed for hitting your ripper when removing slate. For repairs, it’s important to carry a restoration hammer. It is useful working in valleys, places where cuts need to be made, and installing new courses of slate. A slate hammer is used for cutting, nailing, and hammering nails. Restoration Hammer – A restoration hammer and a slate hammer are two separate hammers. A slate hook also costs much less than a copper bib. Most prefer the slate hook method because nails can damage other slate and bibs can fall out or rust. Stainless hooks are stronger and will work better for harder decking but the aesthetics of copper may be appealing to some.Īnother method for holding replacement slates in place is the nail and bib method. Copper and stainless are material options. A new piece is then inserted up into the slate and slid down onto the hook. A hook is lined up with the course below, and then hammered into the decking. Slate Hooks – Once a piece of slate has been removed, the most common means of replacing the slate is a slate hook. ![]() Once the ripper is slid under the broken slate, the ears hook onto the nail and hammering back on the ripper’s handle will remove the nails to allow the slate to be removed. The flex is also important as a rigid blade can do more damage than good. The Stortz ripper is a one piece forging which has superior strength to a welded ripper. If a ripper is too thick, it can break adjoining slates. A thin, strong blade are the desired qualities. The ripper is the best way to achieve this. Stortz Slate Ripper – Once you have the ability to access the roof, it’s time to remove the broken slates. This process can be repeated up the roof as necessary to reach repair areas or to install fall protection for all workers. The SLATOR has a built in OSHA compliant anchor point for fall protection. The first SLATOR is generally installed near the eve of a roof. The SLATOR is screwed into the roof rafters with approved fasteners and then a ladder is firmly clamped into the SLATOR. Unlike a ridge hook, the SLATOR can be used on hip roofs and other places where the ridge is inaccessible. Slator – The SLATOR (Secure Ladder And Tie Off Responsibly) is a newer product for giving roofers simple and safe access on slate roofs. Video provide by Joe Jenkins and the Slate Roof Warehouse. Always secure the plank to the bracket with a nail or screw. Make sure the lock is engaged! These brackets allow a 2″x 10″ to be inserted between the brackets and allow access to the roof. A lot of weight will be put on these brackets so this securing it properly is essential. ![]() The tongue portion hooks onto a roofing nail (at least a 16 penny nail, 3 1/2″) and then 2 more are then used to secure the bracket. Slate Brackets – Qualcraft is the manufacturer of a slate roof bracket which is commonly used for staging a slate roof.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |